Cladding Installation FAQs
Straight answers to the questions we're asked most.
How much does cladding cost per square metre in the UK?
Fitted exterior cladding typically costs £70 to £180 per square metre in the UK in 2026, depending on the material. Larch and thermally modified timber sit around £70 to £120, composite and fibre cement around £85 to £160, and cedar up to £180. Standing seam metal costs £180 to £320. Scaffolding, removal of old finishes and complex detailing are extra.
Do I need planning permission to clad my house?
In England, cladding a house is often permitted development if the materials are similar in appearance to the existing house. In conservation areas, National Parks, Areas of Outstanding Natural Beauty and on listed buildings, cladding normally needs planning permission or listed building consent. Rules differ in Scotland, Wales and Northern Ireland, so check with your council before ordering materials.
What is the best cladding for a house?
The best cladding depends on budget, maintenance and fire requirements. Fibre cement is durable, colour-stable and non-combustible or limited combustibility. Larch and cedar look natural but need care if you want to keep the original colour. Composite is low maintenance but usually combustible. For walls close to a boundary or on taller homes, a non-combustible board is often required.
How long does timber cladding last?
Well-installed larch or cedar cladding commonly lasts 30 to 40 years or more, and thermally modified timber has a similar service life when detailed correctly. Longevity depends far more on installation than species. A ventilated cavity, stainless fixings, boards kept off the ground and good drainage details stop the timber from staying wet, which is what causes rot.
Does cladding need a gap behind it?
Yes, nearly all cladding systems need a ventilated cavity behind the boards, usually at least 25mm, created with vertical battens. The gap lets rain that gets past the boards drain away and allows air to dry the back of the cladding. Insect mesh at the top and bottom keeps out wasps and rodents while still letting air flow through.
Can you put cladding over brick?
Yes, cladding can be fitted over sound brick or blockwork. The installer fixes a breather membrane and treated battens to the wall using suitable masonry fixings, then attaches the boards. The wall must be dry and structurally sound first. Window sills and reveals often need extending, because the cladding adds around 50mm to 70mm to the wall thickness.
Is composite cladding better than timber?
Composite cladding is better if you want minimal maintenance and consistent colour, while timber is better for a natural look and lower environmental impact. Composite does not need oiling and resists rot, but it expands more with heat and is usually combustible. Timber weathers and may need treatment, yet it can be repaired board by board and is often cheaper.
Does timber cladding need treating?
Durable species such as larch, cedar and thermally modified timber do not need treating to resist rot if correctly installed. Left untreated, they weather to a silver grey within one to two years. If you want to keep the original warm colour, apply a UV-protective oil or stain and recoat every two to five years depending on exposure.
How long does it take to clad a house?
Cladding a single-storey extension usually takes two to four days, while a full two-storey detached house can take one to three weeks. Time depends on the wall area, scaffolding, the number of windows and corners, and whether existing render or cladding must be removed first. Weather can also cause delays, since membranes should not be left exposed for long.
Can cladding help with damp walls?
Cladding can protect a wall from driving rain, which helps where damp is caused by water penetrating through porous brick or cracked render. It will not fix rising damp, leaking gutters or condensation, and covering a wet wall can make problems worse. Always find and fix the cause of damp before cladding, and let the wall dry out first.
Why has my timber cladding gone black?
Black streaks on timber cladding are usually caused by iron fixings reacting with tannins in the wood, especially in oak, cedar and larch. Plain steel or poor-quality galvanised nails are the main culprit. Patchy dark grey can also be natural weathering or surface mould. Stainless steel fixings prevent the staining, and an oxalic acid cleaner can lighten existing marks.
Is cladding allowed close to a boundary?
Combustible cladding is restricted on walls close to a boundary, typically within one metre, under Approved Document B in England. In these locations installers usually recommend fibre cement or metal cladding with a high fire classification. Building control can confirm the requirement for your project, and the installer should check this before quoting for timber or composite.
Get a free cladding installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote