Guide · Homeowners · 4 min read · Updated 17 November 2026
How Is External Cladding Installed? Battens, Membranes and Fixings
Short answer
External cladding is installed by fixing a breather membrane to the wall or sheathing, then treated battens to create a ventilated cavity, then the cladding boards with stainless steel or manufacturer-approved fixings. Insect mesh closes the top and bottom of the cavity while allowing air through. Trims and flashings finish corners, windows and edges. A typical extension takes a few days; a whole house can take two to four weeks.
Why the build-up matters
Cladding is a rainscreen. The boards shed most of the rain, but some water and moisture will always get behind them through joints, gaps and wind-driven spray. The layers behind the cladding exist to deal with that safely. A breathable membrane stops water reaching the structure while letting water vapour escape. The battens hold the boards away from the membrane, creating a cavity where air moves and dries everything out.
When cladding fails, it is rarely the boards themselves. It is usually missing ventilation, untreated battens, the wrong fixings, or poor detailing around windows and at the base of the wall. Understanding the layers helps you judge whether a quote is complete.
| Layer | Purpose | What to expect |
|---|---|---|
| Wall or sheathing | Structure behind the cladding | Masonry, blockwork or boarded timber frame |
| Breather membrane | Weather barrier that lets vapour escape | Lapped and taped at joints and openings |
| Battens | Create a ventilated cavity | Treated timber, commonly 25mm deep or more |
| Insect mesh | Keeps insects out, lets air in | At the base and top of the cavity |
| Cladding boards | Rainscreen and finish | Fixed to battens with suitable fixings |
| Trims and flashings | Close corners, edges and openings | Matching or metal trims |
Step by step on site
The job starts with preparation. Old cladding is stripped, the wall underneath is inspected, and any rotten sheathing or damaged masonry is repaired. Downpipes, lights and cables are temporarily removed. The breather membrane is then fixed from the bottom up so each layer laps over the one below, with taped joints and careful dressing into window and door openings.
Battens go on next, fixed into the structure at regular centres, usually vertical for horizontal boards so air can rise freely. Where boards run vertically, a counter-batten system is used to keep the cavity open. A starter strip and insect mesh are fitted at the base, which should sit well above ground level to avoid splashback. The boards are then fixed working upwards, with joints staggered, ends sealed where required and expansion gaps left for composite products.
- Strip existing cladding and repair the structure behind
- Fix breather membrane, lapped and taped at joints
- Fix treated battens to form a ventilated cavity
- Fit insect mesh at the base and top
- Fix boards with stainless or manufacturer-approved fixings
- Finish corners, reveals, sills and soffits with trims
Fixings and why they matter
Fixings are a small part of the cost but a large part of the result. Timber cladding is typically face-fixed with stainless steel ring-shank nails or screws, two per board at each batten, positioned to allow the wood to move without splitting. Cedar, oak and sweet chestnut contain tannins that react with ordinary steel, causing black streaks, so stainless fixings are essential with these species.
Composite and many fibre cement systems use manufacturer-specified clips or screws. Using the wrong fixings or ignoring spacing guidance can void the product warranty and lead to boards that buckle, crack or work loose. Ask your installer which fixings they intend to use and check they match the manufacturer's instructions.
Details that separate good and poor work
Look closely at the edges. Window reveals should have neat trims or returns, with sills that project far enough to throw water clear of the cladding below. External corners need either mitred boards, corner trims or a vertical corner board. The base of the cladding should stop above ground, with a clear gap and mesh rather than boards touching soil, paving or gravel.
At the top, the cavity should be able to breathe out under the eaves or through a vented closure. Cut ends of timber boards should be sealed with end-grain treatment where the supplier recommends it. Pipes and cables passing through should be sleeved and sealed. These are the areas where cheap installations cut corners and where problems such as rot and staining begin.
Common installation mistakes
Most cladding problems come from a handful of avoidable errors. Boards are fixed straight onto masonry without battens, trapping water against the wall. The base of the cladding runs down to the ground, so boards sit in wet soil or splashback and rot within a few years. Battens are untreated or too thin, so the cavity closes up and air cannot move.
Other common mistakes include plated or bright steel nails that rust and stain, membranes left untaped around windows so water tracks into the frame, and composite boards fitted without the expansion gaps the manufacturer specifies, which then buckle in the summer heat. Sills that do not project past the cladding throw water straight onto the boards below. All of these are invisible once the job is finished, which is why it pays to ask your installer to describe the build-up and to take photos at each stage.
How long it takes and what you need to do
A garden office or small extension can often be clad in two to four days. A full house, with scaffolding, may take two to four weeks depending on the number of elevations, windows and the weather. Timber and fibre cement can be fitted in most weather, but membranes and some trims need dry conditions for taping and sealing.
Before the team arrives, clear plants, furniture and stored items from the base of the walls and make sure there is somewhere to stack materials. Let neighbours know if scaffolding is going up near a shared boundary. We arrange vetted, insured local cladding installers who explain the build-up in writing before work starts, so you know exactly what is going on your walls.
Questions people also ask
Does cladding need a breather membrane?
Yes, in almost all cases. A breather membrane protects the structure from rain that gets behind the cladding while letting water vapour escape outwards. On timber frame buildings it is essential. On masonry, a membrane is still commonly used to protect battens and insulation and to manage moisture.
How big should the gap behind cladding be?
A ventilated cavity of at least 25mm is common, formed by treated battens. Some systems and manufacturers specify more. The cavity must be open at the bottom and top, protected with insect mesh, so air can flow and dry out any moisture that gets behind the boards.
Can cladding be fixed directly to brick?
It should not be fixed directly without battens. Boards are fixed to treated battens, which are fixed to the brickwork, creating a ventilated cavity. Fixing boards tight to masonry traps moisture, leading to rot, staining and failure. A breather membrane is often included between the wall and battens.
Written and checked by the Cladding Installation team. Read our editorial policy.
More guides
How Much Does Cladding Cost in the UK? 2026 Prices per m²
Supplied and fitted cladding in the UK typically costs £70–£120 per m² for larch or Douglas fir, £110–£180 for western red cedar, £90–£160 for…
Timber vs Composite vs Fibre Cement Cladding: Which Is Best?
Timber cladding gives the most natural look and is often cheapest, but it weathers and may need oiling to keep its colour. Composite holds its colour…
Do You Need Planning Permission for Cladding? UK Rules Explained
In England, cladding a house is often permitted development if the materials are similar in appearance to the existing house. In conservation areas,…
How to Maintain Timber Cladding: Weathering, Oiling and Repairs
Timber cladding needs little maintenance if left to weather naturally: an annual inspection, keeping vents and the base clear, and replacing any…
Get a free cladding installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote