Guide · Homeowners · 4 min read · Updated 17 November 2026
How to Maintain Timber Cladding: Weathering, Oiling and Repairs
Short answer
Timber cladding needs little maintenance if left to weather naturally: an annual inspection, keeping vents and the base clear, and replacing any split or loose boards. If you want to keep its original colour, clean and recoat with a UV-protective oil or stain every two to three years. Avoid pressure washing at high settings, which raises the grain, and deal with gutter leaks quickly.
Natural weathering versus coated finishes
Every timber cladding owner faces one choice: let it weather, or keep it coated. Untreated larch, Douglas fir, cedar and thermally modified timber all turn silver-grey when exposed to sunlight and rain. The change usually takes a year or two and can look patchy during the transition, particularly under eaves, beneath window sills and on elevations that get little sun. Once complete, the grey patina is stable and needs little more than inspection.
Coating the cladding with a UV-protective oil or stain keeps the warmer tones, but it commits you to regular recoating. Once you start, stopping leads to a blotchy mix of coated and weathered wood. Decide early, ideally before installation, and tell your installer, because some coatings are best applied before the boards go up so every face and edge is protected.
| Approach | Upkeep | Look over time |
|---|---|---|
| Left to weather | Annual inspection, occasional clean | Silver-grey, patchy during transition |
| UV oil or clear finish | Recoat roughly every 2–3 years | Holds warmer tones if maintained |
| Pigmented stain | Recoat roughly every 3–5 years | Even colour, more protection |
| Paint on softwood | Redecorate every few years | Solid colour, needs sound timber |
An annual maintenance routine
Once a year, ideally in late spring, walk around the building and look closely at the cladding. Check for boards that have split, cupped or come loose, fixings that have popped, and staining that suggests water is running where it should not. Pay attention to the base of the walls, around windows and below gutters, which are the areas most exposed to water.
Keep the ventilation gap at the bottom clear of soil, mulch, gravel and plants. Trim back climbing plants and shrubs that hold moisture against the boards. Check that gutters and downpipes are clear and not leaking onto the cladding, because constant wetting from a dripping gutter will rot even durable timber.
- Look for split, loose or cupped boards
- Check fixings have not popped or rusted
- Keep the base gap and insect mesh clear
- Cut back plants touching the cladding
- Clear gutters and fix leaking joints
- Note any black staining or green growth
Cleaning timber cladding safely
Green algae and dirt build up on shaded and north-facing walls. A soft brush with water and a mild, timber-safe cleaner usually shifts it. For more stubborn growth, a biocidal wash formulated for exterior timber can be used, following the manufacturer's instructions and protecting plants below.
Pressure washers need care. A high-pressure jet can tear up the soft fibres of the wood, leaving a furry surface that holds dirt and weathers unevenly. If you use one, keep it on a low setting with a wide fan nozzle and work along the grain from a sensible distance. Black streaks around fixings often mean ordinary steel has reacted with tannins in the wood; the long-term fix is replacing the fixings with stainless steel.
Repairing damaged boards
Individual boards can usually be replaced without disturbing the rest. On shiplap or tongue and groove cladding, the damaged board is carefully cut out, the fixings removed and a new board of the same species and profile fitted, with the tongue trimmed if needed to slide it into place. On open-joint or feather edge cladding it is simpler.
A new board will look different from weathered ones at first. Untreated replacements usually blend in within a season or two. If the cause of the damage was water, such as a leaking gutter or a missing sill drip, fix that first or the new board will fail in the same way. Soft, crumbling battens behind the boards are a sign of a ventilation or membrane problem that needs a wider repair.
Recoating step by step
If you have chosen a coated finish, timing and preparation decide how long it lasts. Recoat in dry, mild weather when the timber has had several dry days, because oil applied to damp wood will not soak in properly and can peel or go patchy. Start by washing the boards with a timber cleaner to remove dirt, algae and loose fibres, then let them dry fully.
Lightly brush or sand any rough areas and check for bare patches where the old finish has worn through, usually on the most exposed elevations. Apply the oil or stain thinly along the grain, working a few boards at a time to avoid lap marks, and treat cut ends and edges thoroughly. Two thin coats are better than one heavy coat. Always follow the product instructions on drying times, and keep a note of the product used, because switching between incompatible finishes can cause adhesion problems on the next recoat.
When to call in a specialist
Call a cladding specialist if you see widespread soft or rotten boards, damp patches inside, failed membrane visible through gaps, or boards that have been fixed directly to masonry without a cavity. These suggest the system behind the cladding is not working, and replacing boards alone will not fix it.
Upper-floor maintenance also needs proper access. Under the Work at Height Regulations 2005, anyone working at height must plan the work and use suitable equipment, so recoating a two-storey elevation usually means a tower or scaffold. We arrange vetted, insured local cladding specialists for repairs, recoating and full re-cladding when the time comes.
Questions people also ask
Do you have to treat larch cladding?
No. Larch heartwood is naturally durable and is often left untreated to weather to a silver-grey. Treating it with a UV-protective oil or stain is optional and only needed if you want to keep the original colour. Once you start coating, you need to keep recoating regularly to avoid an uneven look.
How often should cedar cladding be oiled?
If you want to maintain the original colour, every two to three years is typical, depending on exposure. South-facing and coastal elevations may need it more often. Clean the boards first and use a product designed for exterior timber. If you are happy for cedar to go grey, it does not need oiling.
Why is my timber cladding going black?
Black streaks near fixings usually mean ordinary steel nails have reacted with tannins in the timber, common with cedar and oak. General black or green discolouration is often mould or algae on damp, shaded walls. Clean with a timber-safe product, improve drainage and ventilation, and replace corroding fixings with stainless steel.
Written and checked by the Cladding Installation team. Read our editorial policy.
More guides
How Much Does Cladding Cost in the UK? 2026 Prices per m²
Supplied and fitted cladding in the UK typically costs £70–£120 per m² for larch or Douglas fir, £110–£180 for western red cedar, £90–£160 for…
Timber vs Composite vs Fibre Cement Cladding: Which Is Best?
Timber cladding gives the most natural look and is often cheapest, but it weathers and may need oiling to keep its colour. Composite holds its colour…
Do You Need Planning Permission for Cladding? UK Rules Explained
In England, cladding a house is often permitted development if the materials are similar in appearance to the existing house. In conservation areas,…
How Is External Cladding Installed? Battens, Membranes and Fixings
External cladding is installed by fixing a breather membrane to the wall or sheathing, then treated battens to create a ventilated cavity, then the…
Get a free cladding installation quote
Tell us what you need and we'll come back with a clear price.
Request a quote